Griffin: updated thumbnail image

2022-02-21T21:52:39Z

updated thumbnail image

← Older revision		Revision as of 21:52, 21 February 2022
Line 1:		Line 1:
	__NOTOC__		__NOTOC__
	[[File:~~Lulzbot-AO100~~.jpg\|thumb\|right\|300px]]		[[File:chungus_front.jpg\|thumb\|right\|300px]]

	= Zone =		= Zone =

Griffin: Updates to instructions, prepping for full handoff for general use

2022-02-18T23:18:03Z

Updates to instructions, prepping for full handoff for general use

← Older revision		Revision as of 23:18, 18 February 2022
Line 9:		Line 9:

	== Permissions ==		== Permissions ==
	For general use by members. Maintenance beyond changing filament not allowed except if given permission. Treat equipment as if it were your own and put away as or better than you found it.		For general use by members. Maintenance beyond changing filament is not allowed except if given explicit permission. This includes removing the glass bed, bed leveling, and nozzle changes. Treat equipment as if it were your own and put away as or better than you found it.

	== Restrictions ==		== Restrictions ==
	* Use only with the online interface (currently at http://end on the LAN)		* Use only with the online interface (currently at http://end on the LAN)
	* Use with 1.75mm PLA or PLA variants only		* Use with 1.75mm PLA or PLA variants only. Do not use PETG as this will destroy the bed.
	* Use the custom Cura profile only to print with this machine (TODO: provide profile file, make profiles for other slicers)		* Use the custom Cura profile only to print with this machine (TODO: provide profile file, make profiles for other slicers)

Line 21:		Line 21:

	= Basic Instructions =		= Basic Instructions =

	* On any computer you are allowed access to, connect to the Freeside network and access the web interface using http://end (TODO: Change the printer hostname)		* On any computer you are allowed access to, connect to the Freeside network and access the web interface using http://end (TODO: Change the printer hostname)
	* Upload the desired gcode file to the 'Jobs' tab of the interface		* Upload the desired gcode file to the 'Jobs' tab of the interface
	* Click the desired file and begin print		* Click the desired file and begin print
	* Do not level the bed, this falls under maintenance and is ~~an entire process (see above)~~		* Do not level the bed, this falls under maintenance and is not allowed
	* ~~Machine~~ can stay on indefinitely and should be left on, it doesn't like starting up ~~and delivering the interface~~ on the Freeside network		* The machine can stay on indefinitely and should be left on, it doesn't like starting up on the Freeside network very much

	== Basic Operational Knowledge ==		== Basic Operational Knowledge ==
	~~(TODO: This whole section)~~		* How to home:
	* How to home		Go to the main page on the web interface and select the 'Home' button in the axes section
	* How to slice and send a ~~job~~ to it		* How to slice and send to the printer:
			The 3D printing room has a computer with the correct profile installed in Cura.
			Select the Chungus machine in Cura and the Chungus Standard profile.
			Open your model(s) and slice as normal. If you need to enable or disable supports, do so, but do not change any other settings.
			Export the files somewhere on the computer.
			Open the web interface and click the 'Jobs' tab.
			Click the 'Upload G Code' button, select your file, and wait for the upload.
			Click the file you just uploaded in that same tab to begin the print.
	* How to abort a failed job		* How to abort a failed job
	* How to properly remove a print once it has completed		Click the 'Pause' and/or 'Stop' button on the 'Status' page on the web interface.
	* How to load and unload filament ~~(optional~~, ~~but you'll be stuck~~ with the ~~loaded plastic type~~ and ~~color~~)		If a print is particularly bad or the printer is at risk of damage' press 'Emergency Stop' in the top right corner.
			* How to properly remove a print once it has been completed
			Prints should self-release from the glass. It may take a small bit of force but you can just lift a print from the bed.
			* How to load and unload filament
			Heat up the hotend to 200c
			When at temperature, pull the lever on the extruder and pull out the current filament
			Pull off the spool and replace it with a new one
			Lead the filament underhand and around the holder (TODO: insert image) into the extruder, doing this is any other way causes feeding issues at the moment
			Use the lever again to push the new filament into the hotend
			Wait a few seconds and use the interface to extrude some filament
			If all looks good, disable the hotend using the interface
			If something went wrong, contact Griffin

	== Advanced Operational Knowledge ==		== Advanced Operational Knowledge ==
Line 41:		Line 58:
	== Cura Preconfigured Profiles ==		== Cura Preconfigured Profiles ==
	(TODO: Upload Cura print profile(s))		(TODO: Upload Cura print profile(s))
			* Chungus Standard - Uses 0.2mm layer heights and a small brim to prevent warping. This is a good all around profile.

	== Other Preconfigured Profiles ==		== Other Preconfigured Profiles ==
Line 46:		Line 64:
	(TODO: Simplify 3D profile)		(TODO: Simplify 3D profile)
	(TODO: PrusaSlicer profile)		(TODO: PrusaSlicer profile)

	~~=== Print Profiles ===~~
	~~(TODO: Fill out based on uploaded files)~~

	~~=== Filament Profiles ===~~
	~~This machine only uses PLA. Other filament profiles may be added for PLA+, HTPLA, PLA/PHA, etc. Just print at ~215C on the hotend and 60C on the bed.~~

	== Specifications and Detailed Instructions ==		== Specifications and Detailed Instructions ==
Line 57:		Line 69:

	= Warnings =		= Warnings =
	~~TODO: specify warnings~~		* This machine can only use PLA and PLA variants. Do not use PETG EVER. Do not print higher temp materials on Chungus, use the [[High Temp Printer]] for that.
			* Do NOT level this machine manually or with mesh leveling. It is well tuned and leveling is a long process. Contact Griffin if you think the print it out of level.
			* This printer is very large. Be mindful of large prints both in terms of hogging the machine and in terms of filament usage.

	== Safety ==		== Safety ==
	~~TODO: specify safety requirements~~		* This machine has an open area in the front. This will hopefully get covered in a screen one day. Until that day, do not be an idiot and go sticking your fingers in there.

			== Proposed Improvements - Anybody is welcome to offer help with these! ==
			* A Duet 5i or 7i touch screen for usability, especially when WiFi decides to be a jerk
			* A new spool holder, especially one that can help accommodate larger filament spools
			* New part cooling duct

Griffin: Griffin moved page Chungus-Printer to Chungus Printer: Aesthetics

2022-02-18T22:43:01Z

Griffin moved page Chungus-Printer to Chungus Printer: Aesthetics

← Older revision	Revision as of 22:43, 18 February 2022
(No difference)

Griffin: Created page

2022-02-16T13:06:09Z

Created page

New page

__NOTOC__
[[File:Lulzbot-AO100.jpg|thumb|right|300px]]

= Zone =
01: [[3D Printing]]

= Owner(s) =
* Griffin Brown

== Permissions ==
For general use by members. Maintenance beyond changing filament not allowed except if given permission. Treat equipment as if it were your own and put away as or better than you found it.

== Restrictions ==
* Use only with the online interface (currently at http://end on the LAN)
* Use with 1.75mm PLA or PLA variants only
* Use the custom Cura profile only to print with this machine (TODO: provide profile file, make profiles for other slicers)

= About =
This is a Creality Ender 5 Plus with a Microswiss direct drive and Duet 3 Mini 5+ mainboard. It has a 350mm x 350mm x 400mm print volume.
While it has a direct drive and could print other filaments, this machine is limited to only PLA for cost and usability reasons.

= Basic Instructions =

* On any computer you are allowed access to, connect to the Freeside network and access the web interface using http://end (TODO: Change the printer hostname)
* Upload the desired gcode file to the 'Jobs' tab of the interface
* Click the desired file and begin print
* Do not level the bed, this falls under maintenance and is an entire process (see above)
* Machine can stay on indefinitely and should be left on, it doesn't like starting up and delivering the interface on the Freeside network

== Basic Operational Knowledge ==
(TODO: This whole section)
* How to home
* How to slice and send a job to it
* How to abort a failed job
* How to properly remove a print once it has completed
* How to load and unload filament (optional, but you'll be stuck with the loaded plastic type and color)

== Advanced Operational Knowledge ==
This is a loanation and a somewhat custom machine. Any advanced use will only be permitted on a case-by-case basis because of this. Just print PLA on it and be graced by the large lad.

== Cura Preconfigured Profiles ==
(TODO: Upload Cura print profile(s))

== Other Preconfigured Profiles ==
(TODO: Slic3r profile)
(TODO: Simplify 3D profile)
(TODO: PrusaSlicer profile)

=== Print Profiles ===
(TODO: Fill out based on uploaded files)

=== Filament Profiles ===
This machine only uses PLA. Other filament profiles may be added for PLA+, HTPLA, PLA/PHA, etc. Just print at ~215C on the hotend and 60C on the bed.

== Specifications and Detailed Instructions ==
TODO: complete specifications, links to documentation, etc.

= Warnings =
TODO: specify warnings

== Safety ==
TODO: specify safety requirements

Chungus Printer - Revision history

Griffin: updated thumbnail image

Griffin: Updates to instructions, prepping for full handoff for general use

Griffin: Griffin moved page Chungus-Printer to Chungus Printer: Aesthetics

Griffin: Created page